root@nas:/root# smartctl -a /dev/sdc 14:34:56
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.0.9-100.fc28.x86_64] (local build)
=== START OF INFORMATION SECTION ===
Model Family: Hitachi/HGST Ultrastar 7K4000
Device Model: Hitachi HUS724030ALE641
Serial Number: P8GH7GVR
LU WWN Device Id: 5 000cca 22cc6eda4
Firmware Version: MJ8OA5F0
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Sep 20 14:34:56 2019 MDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 1) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 84
3 Spin_Up_Time 0x0007 136 136 024 Pre-fail Always - 479 (Average 440)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 52
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 9
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 121 121 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 39864
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 51
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 618
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 619
194 Temperature_Celsius 0x0002 200 200 000 Old_age Always - 30 (Min/Max 22/43)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 11
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 6
SMART Error Log Version: 1
ATA Error Count: 18 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 18 occurred at disk power-on lifetime: 28437 hours (1184 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 10 00 00 00 Error: ICRC, ABRT at LBA = 0x00000010 = 16
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 18 00 00 00 e0 08 00:06:24.870 WRITE DMA
47 00 01 12 00 00 a0 08 00:06:24.870 READ LOG DMA EXT
47 00 01 00 00 00 a0 08 00:06:24.869 READ LOG DMA EXT
ef 10 02 00 00 00 a0 08 00:06:24.869 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 00:06:24.869 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 17 occurred at disk power-on lifetime: 28437 hours (1184 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 10 00 00 00 Error: ICRC, ABRT at LBA = 0x00000010 = 16
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 18 00 00 00 e0 08 00:05:54.271 WRITE DMA
47 00 01 12 00 00 a0 08 00:05:54.271 READ LOG DMA EXT
47 00 01 00 00 00 a0 08 00:05:54.271 READ LOG DMA EXT
ef 10 02 00 00 00 a0 08 00:05:54.271 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 00:05:54.271 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 16 occurred at disk power-on lifetime: 28437 hours (1184 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 a8 a3 50 0d Error: ICRC, ABRT at LBA = 0x0d50a3a8 = 223388584
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 38 00 00 00 40 08 00:05:23.163 WRITE FPDMA QUEUED
61 18 30 98 a3 50 40 08 00:05:23.163 WRITE FPDMA QUEUED
47 00 01 12 00 00 a0 08 00:05:23.163 READ LOG DMA EXT
47 00 01 00 00 00 a0 08 00:05:23.162 READ LOG DMA EXT
ef 10 02 00 00 00 a0 08 00:05:23.162 SET FEATURES [Enable SATA feature]
Error 15 occurred at disk power-on lifetime: 28437 hours (1184 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 10 00 00 00 Error: ICRC, ABRT at LBA = 0x00000010 = 16
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 18 98 a3 50 40 08 00:04:52.054 WRITE FPDMA QUEUED
61 18 10 00 00 00 40 08 00:04:52.054 WRITE FPDMA QUEUED
47 00 01 12 00 00 a0 08 00:04:52.054 READ LOG DMA EXT
47 00 01 00 00 00 a0 08 00:04:52.054 READ LOG DMA EXT
ef 10 02 00 00 00 a0 08 00:04:52.054 SET FEATURES [Enable SATA feature]
Error 14 occurred at disk power-on lifetime: 28437 hours (1184 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 a8 a3 50 0d Error: ICRC, ABRT at LBA = 0x0d50a3a8 = 223388584
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 f0 00 00 00 40 08 00:04:21.201 WRITE FPDMA QUEUED
61 18 e8 98 a3 50 40 08 00:04:21.201 WRITE FPDMA QUEUED
47 00 01 12 00 00 a0 08 00:04:21.200 READ LOG DMA EXT
47 00 01 00 00 00 a0 08 00:04:21.200 READ LOG DMA EXT
ef 10 02 00 00 00 a0 08 00:04:21.200 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 28435 -
# 2 Vendor (0xb0) Completed without error 00% 28182 -
# 3 Vendor (0x71) Completed without error 00% 28182 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.